How To Pair Xfinity Window Sensor
Door/Window Sensor Installation Guide Introduction Door/Window sensors are designed to secure the perimeter of the residential premise, and provide the ability to add various automation services. The Door/Window sensor, which consists of a magnet that attaches to a door or window, will communicate door events to the home security organization. When the magnet is moved abroad from the sensor, a point will be sent to the control console that communicates the inverse state to the security system. Signals tin can besides be used to actuate a chinkle or convenience lighting based on system settings. Specification Frequency Battery Type Operating Temperature Storage Temperature Bombardment Life Dimension 2.4GHz CR2450 Battery 0 C to 50 C (32°F - 122°F) -20 C to 60 C (-4°F - 140°F) 5 Years Sensor Device: 59 mm x 29 mm x 11 mm (2.32" x 1.14" x 0.43") Magnet: 59 mm 10 x mm x eleven mm (two.32" ten 0.39" x 0.43") Spacer: 59 mm x 10 mm x 2 mm (2.32" x 0.39" 10 0.078") Pairing Sensor This Door/Window sensor needs to be paired earlier installation. i. Pull the exposed plastic tab from the sensor. (Figure ane) 2. The LED indicator will exist lit for two seconds to indicate a Successful booting. 3. It will blink 3 times every five seconds while scanning the network. 4. If network is not found afterward 100 seconds, the sensor will become into sleep mode. To wake the sensor once again, you demand to use magnet or tamper (Figure 2) to trigger a dent process, and then sensor will repeat steps from 3 to 4. Effigy ane Figure two Installation one. two. 3. 4. Please make certain that the sensor and magnet is located less than 0.25 inch from each other. For optimal functioning, it is highly recommended to install the Door/Window sensor on the stock-still frame and the magnet on the moving part of the door/window. Place the sensor most the top of the door that close to the opening edge of the door. This is the mounting location for the sensor. Apply the provided double-sided tape on the sensor. Adhere the sensor to the door. Press firmly and hold in place for a few seconds (Figure 3). Secure it with silicone if needed. Employ provided double-sided tape on the magnet. Make sure the alignment of both sensor and magnet are facing each other (Figure 4). Printing firmly and hold in identify for a few seconds. Secure it with silicone if needed. Spacers are used to raise the level of the magnet to be level/closer to sensor. Install Magnets as shown in Figure 5 Operation 1. 2. The Greenish Pairing LED will stay off during the normal operation. The sensor is equipped with a tamper switch. If the cover of sensor is removed, the sensor will send an alarm to the home controller or security system. Reset to Factory Defaults & Reboot If sensor needs to be manufactory defaulted (for instance, to prepare it for joining with a dwelling controller or security system). ane. Remove sensor cover. 2. Remove the battery from sensor. 3. Depress the tamper switch for three seconds before inserting the bombardment. iv. Insert the bombardment. The sensor should illuminate the LED in one case when boot-up/initialization tasks are complete. 5. Release the tamper switch while the LED is illuminated (information technology will be lit for 4 seconds). The sensor should then reset to mill default settings and begin searching for any available home controller or security system. If you lot need to reboot the device, remove the battery for at least 5 seconds, then re-insert the battery. 6. Place the embrace back on sensor. Notation: Replace Battery with Panasonic CR2450 or Sony CR2450 merely. Utilize of another bombardment may negatively impact the performance of the product. Troubleshooting If device has trouble with pairing to the dwelling controller or security system: one. Separate the sensor and magnet or trigger tamper. The sensor volition re-try to pair. ii. If device continues to accept trouble pairing, remove the bombardment for 5 seconds and so re-insert it. 3. If device continues to have trouble pairing, use "Reset to Factory Defaults" procedure to endeavour pairing again. If device was communicating with the home controller or security organization just is no longer communicating: 1. Move the device to a location closer to the controller. Split up and close the magnet or trigger tamper from the sensor. If the controller successfully shows the sensor's status, and then install a repeater so the system's range can attain the desired location for the sensor. two. If the device has been in use for months or years and the failure is sudden, check the controller to see if the device has a low battery. Follow the instructions provided to supersede the battery. Certification FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Role 15 of the FCC Rules. These limits are designed to provide reasonable protection confronting harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if non installed and used in accordance with the instructions, may crusade harmful interference to radio communications. Yet, there is no guarantee that interference will not occur in a detail installation. If this equipment does crusade harmful interference to radio or idiot box reception, which can be determined by turning the equipment off and on, the user is encouraged to try to right the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a excursion dissimilar from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Y'all are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Role 15 of the FCC Rules. Operation is subject to the following two weather: (1) This device may not crusade harmful interference, and (2) This device must accept whatsoever interference received, including interference that may cause undesired functioning. ETL Statement: This device conforms to ANSI/UL STD 634
| Document ID | 2922539 |
| Awarding ID | 0CiBWBVK8WJj3neSKZaAQQ== |
| Certificate Description | User Manual |
| Download: |  |
| Mirror Download [FCC.gov] | |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 10.56kB (131949 bits) |
| Appointment Submitted | 2016-03-08 00:00:00 |
| Appointment Available | 2016-03-08 00:00:00 |
| Creation Engagement | 2016-02-05 fifteen:25:01 |
| Producing Software | Acrobat Distiller 9.5.5 (Windows) |
| Certificate Lastmod | 2016-02-05 15:25:01 |
| Document Championship | User Manual |
| Document Creator | PScript5.dll Version 5.ii.2 |
| Certificate Author: | jmendez |
Source Exif Data [exif.tools]:
File Type : PDF File Blazon Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yep Writer : jmendez Create Date : 2016:02:05 fifteen:25:01-08:00 Change Date : 2016:02:05 15:25:01-08:00 XMP Toolkit : Adobe XMP Cadre four.ii.ane-c043 52.372728, 2009/01/xviii-xv:08:04 Format : application/pdf Creator : jmendez Title : Microsoft Word - Comcast Xfinity Home Contact Sensor Manual.doc Creator Tool : PScript5.dll Version 5.ii.2 Producer : Acrobat Distiller ix.v.5 (Windows) Document ID : uuid:4e0cf7f6-21bd-4306-9ed2-828833c64640 Instance ID : uuid:d25443f7-6d2c-40a0-8a8c-c2d86f363cdd Page Count : 2
Source: https://fccid.io/MG3-4460/User-Manual/User-Manual-2922539
Posted by: ransdellnotle1998.blogspot.com
0 Response to "How To Pair Xfinity Window Sensor"
Post a Comment